Sex dolls are very delicate sex toys. Sometimes, due to carelessness, or due to a long time of use, the sex doll is damaged, but the damage is relatively small. It is a pity to discard it, but it will cost a lot if you return the doll to the factory for repair. This will make you hesitant, it is better to fix it yourself.

How to repair wear and abrasion?

Easily repair neck or leg, arm or body wear

If the sex doll is not used properly, it may cause structural hazards and cause damage. In other words, there are two ways to repair this damage.

Preparation and process

In order to make this process work normally, please find the damaged part that has been torn, and then use a thin-head tool to glue the TPE on it. After that, pull the sides of the laceration together. Make sure to hold the patch for a minute or two and the patch will be intact again.

 1. Doll preparation procedure

In order to maximize the effectiveness of TPE glue, please consider using a cleanser (such as cleanser, soap, nail polish cleanser or makeup remover) to clean the damaged area. At the same time, do not leave water stains on the surface of the doll's skin. Always keep it dry and clean.

2. Place sex dolls correctly

In other words, it is very important to consider the posture of the sex doll. Ensure that the wound area is in a horizontal position. This will ensure that the amount of glue applied is limited to the wound and will not overflow and break. At the same time, meticulousness is essential. Each step requires one minute of accuracy; otherwise, the results will be far from satisfactory. There will be uneven bonding to the symmetry aspect of the destructive doll.

3. The hot air procedure can repair the skin abrasions of the doll

You can buy common heat guns on websites or online stores. They have an advantage because there is an additional temperature sensor that you can use to monitor the heat applied. They have a digital interface and perform well.

4. Clean the surface

start using baby oil or petroleum jelly to clean the surface of the skin. This part is crucial because it serves two purposes. One, you will get a clean and sterile skin surface; second, the applied heat will be more evenly distributed. Therefore, if you don't want to burn the baby's skin at the end, you must oil it.

5. Use a heat gun on the affected area

Then, focus the heat gun on the skin. Pay attention to the distance between the device and the skin of the doll. Do not focus it too close, otherwise it will cause severe burns and cause disaster. Keep a distance of about four inches from the wound skin area.

6. Reach the required temperature

In other words, the melting temperature is about 110 degrees Celsius. Then, you will notice the mirror glaze produced by heating. By looking at the intensity of the smoke generated by heating, you will know when to stop raising the temperature. Heat the skin of the sex doll to the desired temperature.

7. Glue

1. First, remove any dirt or excess oil on the critical area to be treated. You can do this by wiping the area with 70% isopropyl alcohol.
2. Open the wound with gloved hands.
3. Then use a spatula to evenly apply the TPE repair coating solvent on the inner surface of the wound. At the same time, please avoid excessive glue falling from the tip of the scraper, and replace the glue bottle cap to prevent the solvent from evaporating.
4. Use a spatula to wipe both sides of the inside of the tear.
5. Then pull the two sides of the tears together, and let the TPE repair solvent stick the wound to the wound. Keep the wound closed for a period of time.
6. Wipe off the excess with a paper towel or a clean cloth. The excess will be squeezed out of the tears after the binding. When doing so, please avoid using your fingers, as this will leave unnecessary marks and impressions.
7. Make sure that there is no tension on the surface of the doll and will not cause pressure on the rejoined wound.
8. The position of the doll should be such that there will be no tension on the critical surface for the next 24 hours.

8. Gently repair wear

Then grab a piece of cloth and use a feather to smooth the uneven surface caused by wear. Keep up with several iterations of heating and cooling, and repeat multiple times. This is the key to a good appearance, because each time you repeat the heating and cooling process, you can make it smoother.

At the same time, you still have 30 seconds to eliminate wear. Needless to say, the temperature drops quickly, and you must seize this moment to make the work as smooth as possible.

Intimate tips

At the same time, repeated heating and cooling of the doll will cause the oil to dry out. Therefore, the oil must be re-oiled after each iteration. This is very important because keeping it moist will give you a good finish.

In other words, after repeating the heating and cooling process several times, you will see satisfactory results. After completing all the steps, apply a little powder to achieve an excellent finish. Applying powder here is very useful because it blends with the texture and makes the repair almost invisible.
Make sure you are in an open place and wear a mask to avoid inhaling unnecessary fumes and harm your health.

In addition, when using high temperature equipment, please use the infrared gun carefully to avoid overheating or burning.

This article provides reference materials and reference materials, you can try it, I hope it will be helpful to you.

Also in News