ORDER NOW! GET 10% DISCOUNT, CODE:10% OFF
November 05, 2020
Cleaning up the doll scientifically can extend the life of the doll. Sometimes not all parts of the doll need to be cleaned, just a few parts. At this time, I want to share my personal experience.
To clean any openings, we recommend using a water sprayer to spray water into the openings so that water can flow out of the openings. If there is no sprinkler, but the temperature is low and gentle, you can use the shower hose attachment. To
Also, you can simply use a damp (soft) cloth to clean manually with warm soapy water. Make sure to thoroughly clean all areas of the opening.
You can also clean the opening while showering or bathing the doll with your hands or a small sponge (please refer to the description of the skeleton above)
Use all cleaning methods-let the doll's legs open slightly, open the vagina and anus to the air, and dry naturally. Do not separate the doll's legs too far, as this may cause damage over time.
After the doll is completely dry, use a small amount of petroleum jelly to make holes.
Do not use abrasive soaps or any other harsh chemical cleaning products.
Remove the head from the body
If possible, remove the wig.
Apply a warm antibacterial sponge or cotton cloth dipped in soapy water and gently massage the face.
Please note: Make-up is semi-permanent and can be faded or removed with mineral oil, so it is best to avoid excessive cleaning or rubbing to maintain the life of the make-up.
Take special care not to damage the eyes and eyelashes and avoid wetting these areas.
If you want to remove your eyes before cleaning, you can gently pull the slot to remove it from the front, taking care not to damage the eyelashes.
Gently pat the face with a dry non-abrasive cloth, let it air dry, and then reattach it to the body.
Ensuring that the doll is completely dry is important to limit the chance of damage. To
Gently pat dry with a clean soft cotton cloth to allow the skin to fully air dry.
After drying, you can apply a little powder on the doll, as this will prevent damage caused by friction. Do not dust the powder because it may be very dry and draw out the oil in the TPE. Do not dust frequently. To
Many people recommend using petroleum jelly at the orifice as a protective measure and lubricant.
The wig should always be removed from the doll's head before cleaning.
It is best to comb the wig first, and then clean it from the beginning. To
If the hair is very long, it is easiest to wash it in a small wash basin. Even a shower is great.
Fill the basin with cold water and add a coin-sized soapy water to make a mini "bubble bath" for the wig. Shampoos that do not contain sulfates are the best.
You need to use cold water, otherwise you may lose your style, such as curly hair. To
Immerse the wig and stir gently, then let it stand for about 5 minutes to soak. To
Drain the sink and rinse gently from the top until the water is clear-no bubbles.
We recommend combing the hair directly after cleaning and letting the wig dry on the wig holder. Any curly hair/style will rebound. To
Do not let the wig dry on the doll's head.
Do not use hairdressing products to modify the hair, otherwise it may damage the skin and face of the sex doll.
Put the doll in a neutral position.
Align the fallen (loose) nail with the bare nail. This will determine which nail matches which finger.
After selecting the nails, apply a thin and even layer of glue on the exposed nail area. First make sure that the area is clean and dry, free of dust or talc.
Do not over-apply glue to achieve even and thin coverage. Avoid applying too much to avoid spilling outside the nail area.
After proper alignment, press and hold the nail for 5 seconds-do not touch any glue.
Excess glue is difficult to remove, so it is best to avoid any overflow completely. In case the glue overflows, please use a microfiber cloth and hot soapy water to remove the glue immediately.
To remove the nail, use a set of tweezers, and then gently pull the nail out of the doll toward you (with gentle movements to avoid any damage).
Put the doll in a neutral position.
With one hand, gently and carefully pull the eyelids (up and down, left and right), not to touch the eyelashes or make-up.
Use your other hand to remove your eyes and remove all packaging.
"Shrink" the packaging into new eyes.
Separate the eyes with one hand and do not touch the eyelashes or makeup.
Use the other hand to insert the new eye into the slot and adjust it.
replacing the local position of the TPE doll. I hope to help readers and better maintain the doll. (With reference and borrowing from others' materials)
Comments will be approved before showing up.
July 09, 2021
June 30, 2021
The sex dolls with the head and body separated are the sex dolls that the head and body are made separately, and after all the crafts are completed, the sex doll is finally assembled together.
The all in one sex dolls are the sex dolls which the head and body are poured together to form full size sex doll .
The biggest difference between the two is whether there is an obvious gap in the neck of the sex doll. The sex dolls with an obvious gap are the sex dolls with the head and body separated. The head and body of these sex doll are connected together by screws and screw ports. There is no obvious gap at the joint of the neck of all in one sex doll. It looks more like a real person.
June 23, 2021